{"title":"PEX Fittings \u0026 Tubing","description":"\u003cp\u003ePEX crimp and push-fit fittings, tubing, rings, and manifolds for potable water and hydronic systems — tees, elbows, couplings, adapters, and PE-Xb pipe.\u003c\/p\u003e","products":[{"product_id":"brass-pex-b-barb-tee","title":"1\/2\" Brass PEX Tee (Crimp F1807) — Lead-Free DZR, cUPC Certified","description":"\u003cp\u003eEvery fixture a water line feeds starts at a branch, and the branch starts with a brass PEX tee — one 1\/2″ run split into two without adapters, unions, or a soldered joint. This is the fitting a repipe consumes by the box: forged from lead-free DZR brass, machined to ASTM F1807, and seated with standard copper crimp rings or stainless steel pinch clamps, so it works with the crimp tool already in the pouch. Rated to 100 psi at 180°F, it carries potable water and hydronic heating alike on any SDR-9 PEX — A, B, or C. The tee reads side × side × middle, and this one runs 1\/2″ across all three legs, the size that feeds most sinks, toilets, and fixture loops in a residential build. Available as a single for the service call or a 50-pack for the rough-in, it holds its seal through pressure testing and disappears into the wall the way good rough-in hardware should — specified once, then forgotten for the life of the system.\u003c\/p\u003e","brand":"DN Group Inc.","offers":[{"title":"1 Pack","offer_id":42274047819870,"sku":"611111-BPT","price":1.73,"currency_code":"CAD","in_stock":false},{"title":"50 Pack","offer_id":42437401903198,"sku":"611111-BPT-50","price":78.05,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0605\/0073\/8142\/files\/ChatGPTImageDec12_2025_04_38_55PM.png?v=1765575544"},{"product_id":"brass-pex-b-barb-90-degree-elbow","title":"1\/2\" Brass PEX 90° Elbow (Crimp F1807) — Lead-Free DZR, cUPC Certified","description":"\u003cp\u003ePEX bends, but it doesn't bend sharply — force a tight corner and the tubing kinks. The brass PEX 90° elbow exists for that corner: a forged, lead-free DZR fitting that turns a 1\/2″ line hard through studs, joists, and cabinet backs while the tubing stays relaxed on either side. Machined to ASTM F1807, its barbs seal with standard copper crimp rings or stainless steel pinch clamps — the same tool that does every other fitting on the job. Rated to 100 psi at 180°F and certified for potable water, it serves supply lines and hydronic loops on any SDR-9 PEX — A, B, or C. The bore runs full-flow for the size, so fixtures downstream don't feel the corner. Sold as a single for the service call or a 50-pack for the rough-in, it's the fitting that turns a clean drawing into a clean wall cavity — and then disappears into it.\u003c\/p\u003e","brand":"DN Group Inc.","offers":[{"title":"1 Pack","offer_id":42274048999518,"sku":"611011-BPE","price":0.99,"currency_code":"CAD","in_stock":false},{"title":"50 Pack","offer_id":42437472976990,"sku":"611011-BPE-50","price":44.73,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0605\/0073\/8142\/files\/ChatGPTImageDec12_2025_04_44_03PM.png?v=1765575858"},{"product_id":"brass-90-degree-drop-ear-elbow","title":"1\/2\" Brass PEX Drop Ear Elbow — F1807 × 1\/2\" FPT, Lead-Free DZR","description":"\u003cp\u003eGrab any shower arm and wiggle it — if it moves, someone skipped the drop ear. The brass PEX drop ear elbow is the anchor behind the wall: a 90° fitting with a three-hole mounting flange that screws to blocking, so the shower arm, tub spout, or hose bibb threading into it stays put through decades of daily use. The inlet is a 1\/2″ ASTM F1807 barb that crimps to the PEX supply with a standard copper ring or stainless steel pinch clamp; the outlet is a 1\/2″ female pipe thread that accepts any standard nipple or fixture arm. Forged from lead-free DZR brass and rated for potable hot and cold supply, it belongs in the fixture wall of every bathroom on the plan. Sold as a single for the one-bath reno or a 25-pack for the crew roughing in the whole floor — it's the difference between finish plumbing that feels solid and finish plumbing that rattles.\u003c\/p\u003e","brand":"DN Group Inc.","offers":[{"title":"1 Pack","offer_id":42274050244702,"sku":"611911-BPED","price":3.91,"currency_code":"CAD","in_stock":true},{"title":"25 Pack","offer_id":42831534030942,"sku":"611911-BPED-25","price":87.89,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0605\/0073\/8142\/files\/ChatGPTImageDec12_2025_04_46_15PM.png?v=1765575985"},{"product_id":"brass-male-hose-barb-fitting","title":"1\/2\" Brass PEX × Male Sweat Street Adapter (F1807) — Lead-Free, cUPC","description":"\u003cp\u003eNo room in the joist bay for a stub of copper? That's exactly the job of the brass PEX × male sweat street adapter. Its copper end is sized like 1\/2″ pipe itself, so it solders directly inside an existing elbow, tee, or coupling — no jumper, one less solder joint, an inch of space saved where there wasn't an inch to spare. The other end is a 1\/2″ ASTM F1807 barb that crimps to PEX with a standard copper ring or stainless steel pinch clamp once the soldered side has cooled. Machined from lead-free brass, cUPC certified and rated to NSF\/ANSI 61, it makes the copper-to-PEX handoff exactly where the old system already branches. The order never changes: solder first, let it cool, then crimp — the barb never sees the torch. Sold as a single for the service call or a 50-pack for the van that lives in retrofit country.\u003c\/p\u003e","brand":"DN Group Inc.","offers":[{"title":"1 Pack","offer_id":42437460066398,"sku":"611511-BPSA","price":0.99,"currency_code":"CAD","in_stock":true},{"title":"50 Pack","offer_id":42437460099166,"sku":"611511-BPSA-50","price":44.73,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0605\/0073\/8142\/files\/ChatGPTImageDec12_2025_05_14_00PM.png?v=1765577653"},{"product_id":"brass-pex-to-npt-threaded-adapter-fittings","title":"1\/2\" Brass PEX × FPT Adapter (F1807) — Female Thread, Lead-Free","description":"\u003cp\u003eEvery water heater nipple, threaded valve, and tank fitting ends in male thread — the brass PEX × FPT adapter is how a PEX line grabs onto it. One end is a 1\/2″ female NPT thread that spins onto any standard male pipe thread; the other is a 1\/2″ ASTM F1807 barb that crimps to the tubing with a copper ring or stainless steel pinch clamp. That makes it the stock answer for landing PEX on a boiler drain, a threaded stop, a pump union, or the cold side of a tank — anywhere the equipment side of the job already speaks thread. Machined from lead-free brass for potable hot and cold service, it seals the threaded joint with PTFE tape or pipe dope and the barb side with the same crimp tool as the rest of the system — no torch anywhere in the sequence, which is why threaded transitions are the favourite near finished surfaces. Sold as a single for the service call or a 25-pack for the van.\u003c\/p\u003e","brand":"DN Group Inc.","offers":[{"title":"1 Pack","offer_id":42274100707422,"sku":"611811-BPFA","price":2.24,"currency_code":"CAD","in_stock":true},{"title":"25 Pack","offer_id":42972969205854,"sku":"611811-BPFA-25","price":50.4,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0605\/0073\/8142\/files\/ChatGPTImageDec12_2025_05_32_32PM.png?v=1765578764"},{"product_id":"brass-push-fit-elbow","title":"1\/2\" Brass Push-Fit 90° Elbow — Tool-Free, PEX · Copper · CPVC","description":"\u003cp\u003eSome joints happen where a torch can't go and a crimp tool can't reach — the brass push-fit elbow is built for them. A flooded ceiling bay, a live repair under a full cabinet, two inches of stub in a finished wall: cut the line square, deburr, mark the insertion depth, and push — the stainless steel grab ring bites, the internal O-ring seals, and the 1\/2″ line turns 90° with no tool, no flame, and no ring to gauge. It connects PEX, copper, and CPVC interchangeably, which is what makes push-fit the emergency-repair standard: whatever pipe the wall surprises you with, the same fitting lands on it. Machined from lead-free brass for potable hot and cold service, it's removable with a disconnect clip, so a temporary repair can become permanent — or come apart cleanly when the renovation starts. One in the drawer saves the Sunday call.\u003c\/p\u003e","brand":"DN Group Inc.","offers":[{"title":"1 Pack","offer_id":42274105819230,"sku":"6120011-BPFE","price":4.58,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0605\/0073\/8142\/files\/ChatGPTImageDec12_2025_05_28_58PM.png?v=1765578585"},{"product_id":"brass-push-fit-tee","title":"1\/2\" Brass Push-Fit Tee — Tool-Free Branch Fitting, PEX · Copper · CPVC","description":"\u003cp\u003eAdding a branch to a finished system is the job nobody budgets for — the brass push-fit tee cuts it down to one fitting. Section out a coupling-width of the existing 1\/2″ line, deburr, mark the depth, and push the tee into the gap: two ends rejoin the run, the third sends a new branch wherever the ice maker, hose bibb, or basement bathroom needs it. Each port grips PEX, copper, or CPVC independently, so a copper trunk can grow a PEX branch in one push — no drain-down soldering, no crimp tool swinging in a joist bay. The stainless steel grab rings bite, the internal O-rings seal, and the system is live again in minutes. Machined from lead-free brass for potable hot and cold service and removable with a disconnect clip, it's the fitting that turns \"we'd have to open the ceiling\" into an afternoon job.\u003c\/p\u003e","brand":"DN Group Inc.","offers":[{"title":"1 Pack","offer_id":42274107228254,"sku":"6120111-BPFT","price":7.64,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0605\/0073\/8142\/files\/ChatGPTImageDec12_2025_05_37_21PM.png?v=1765579047"},{"product_id":"brass-push-fit-coupling","title":"1\/2\" Brass Push-Fit Coupling — Tool-Free Repair Splice, PEX · Copper · CPVC","description":"\u003cp\u003eA burst line doesn't wait for the system to drain — the brass push-fit coupling is the splice that doesn't ask it to. Cut out the damaged section, square and deburr the ends, mark the depth, and push the coupling home: the stainless steel grab rings bite, the internal O-rings seal, and the line is back in service with no torch, no crimp tool, and no dry pipe required. Because each end grips PEX, copper, or CPVC independently, it also splices one material straight to another — old copper on one side, new PEX on the other, one fitting in the middle. Machined from lead-free brass for potable hot and cold service, it removes with a disconnect clip if the repair ever becomes a renovation. It's the fitting that ends most flooded-basement stories, which is why one belongs in the kitchen drawer as much as in the service van.\u003c\/p\u003e","brand":"DN Group Inc.","offers":[{"title":"1 Pack","offer_id":42274108309598,"sku":"6120311-BPFC","price":4.09,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0605\/0073\/8142\/files\/ChatGPTImageDec12_2025_05_40_31PM_4420a7db-857c-4a16-a6f6-b2c19c92d667.png?v=1765579713"},{"product_id":"brass-push-fit-cap","title":"1\/2\" Brass Push-Fit Cap — Tool-Free Test Cap, PEX · Copper · CPVC","description":"\u003cp\u003eRough-in done, inspector booked, every stub open — the brass push-fit cap seals them in seconds and unseals them the day the fixtures arrive. It presses onto a 1\/2″ PEX, copper, or CPVC stub, holds the line through the pressure test, and comes back off with a disconnect clip instead of a hacksaw. No torch, no crimp ring, no sacrificed inch of pipe — where a crimped plug is a permanent decision, this cap is a reusable one, moving from stub to stub as each fixture lands. The stainless steel grab ring bites the pipe, the internal O-ring makes the seal, and full insertion is the only technique involved: cut square, deburr, mark the depth, push. Machined from lead-free brass for potable systems, it can also permanently retire a line where code allows an accessible cap. Keep a handful in the van — the fastest closed line in the trade.\u003c\/p\u003e","brand":"DN Group Inc.","offers":[{"title":"1 Pack","offer_id":42274113093726,"sku":"6120401-BPFC","price":2.79,"currency_code":"CAD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0605\/0073\/8142\/files\/ChatGPTImageDec12_2025_05_48_19PM.png?v=1765579734"},{"product_id":"pex-b-tubing-coil","title":"1\/2″ PEX-B Tubing — 100 ft Coil, White · Blue · Red for Hot \u0026 Cold Water","description":"\u003cp\u003eThe advantage of PEX over rigid pipe is the one you feel the first time you pull a run: 100 feet of tubing bends around corners and snakes through joists in a single length, so a bathroom group that would take a dozen copper elbows and as many solder joints becomes one continuous line with a connection only at each end. This is 1\/2″ PEX-B — the cross-linked polyethylene made by the silane (moisture-cure) method — rated for both hot and cold potable water and hydronic heat. It resists scale and won't corrode like copper, and because the wall flexes, it tolerates a freeze that would split a rigid line, expanding rather than bursting. The color is there to keep you organized, not to change the pipe: red for hot, blue for cold, white for either. Terminate it with F1807 crimp rings, stainless cinch clamps, or push-fit fittings. It's the material that turned a plumber's rough-in from a soldering marathon into an afternoon.\u003c\/p\u003e","brand":"DN Group Inc.","offers":[{"title":"White","offer_id":42274120007774,"sku":"6041041","price":33.46,"currency_code":"CAD","in_stock":true},{"title":"Blue","offer_id":42274120040542,"sku":"6041042","price":33.46,"currency_code":"CAD","in_stock":true},{"title":"Red","offer_id":42274120073310,"sku":"6041043","price":33.46,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0605\/0073\/8142\/files\/ChatGPT_Image_Dec_12_2025_06_01_49_PM.png?v=1765580549"},{"product_id":"brass-pex-coupling-splice-crimp-f1807-lead-free-dzr-1-2-3-4-1-reducing-sizes-cupc-certified","title":"1\/2\" Brass PEX Coupling (Crimp F1807) — Lead-Free DZR, cUPC Certified","description":"\u003cp\u003eA line comes up short, a nail finds a run, two coils need to become one — the brass PEX coupling closes the gap. This one joins 1\/2″ PEX to 1\/2″ PEX in lead-free DZR forged brass, machined to ASTM F1807 so it seals with the same copper crimp rings or stainless steel pinch clamps as every other crimp fitting in the pouch. Rated to 100 psi at 180°F and certified to NSF\/ANSI 61 for potable water, it carries supply lines and hydronic loops on any SDR-9 PEX — A, B, or C — and meets CSA B137.5 for Canadian systems. The barbs are full-depth, the shoulders give the crimp ring a clean landing, and the finished splice pressure-tests like the tubing was never cut. Stock a few singles for the service van or the 50-pack for the rough-in cart — it's the smallest fitting on the truck and the one that saves the day most often.\u003c\/p\u003e","brand":"DN Group Inc.","offers":[{"title":"1 Pack","offer_id":42294183100510,"sku":"611311-BPC","price":0.78,"currency_code":"CAD","in_stock":true},{"title":"50 Pack","offer_id":42437129535582,"sku":"611311-BPC-50","price":35.28,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0605\/0073\/8142\/files\/ChatGPTImageDec20_2025_05_29_24PM.png?v=1766269989"},{"product_id":"brass-pex-elbow-adapter-90-1-2-barb-x-1-2-mip-male-thread-lead-free-f1807-crimp-fitting","title":"1\/2\" Brass PEX × MIP 90° Elbow Adapter (F1807) — Lead-Free DZR, cUPC","description":"\u003cp\u003eWhere PEX meets a threaded port in a tight corner, something has to give — the brass PEX × MIP 90° elbow adapter makes sure it isn't the tubing. It handles the turn and the transition in one fitting: a 1\/2″ ASTM F1807 crimp barb on one end, a 1\/2″ tapered male pipe thread on the other, set at a right angle so the line drops into a shower valve, manifold port, or threaded fixture without a strain-inducing bend. Forged from lead-free DZR brass and certified to cUPC and NSF\/ANSI 61, it's rated to 100 psi at 180°F for potable and hydronic service on any SDR-9 PEX. The threads are tapered NPT — a wrap of PTFE tape and a firm wrench-tighten seats them — while the barb end crimps with the same rings and tool as the rest of the system. One elbow for the reno punch list, or a 25-pack for the crew plumbing valve walls all week.\u003c\/p\u003e","brand":"DN Group Inc.","offers":[{"title":"1 Pack","offer_id":42296555929694,"sku":"611044-BPME","price":3.71,"currency_code":"CAD","in_stock":true},{"title":"25 Pack","offer_id":42437364252766,"sku":"611044-BPME-25","price":83.48,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0605\/0073\/8142\/files\/ChatGPTImageDec22_2025_01_22_45PM.png?v=1766427894"},{"product_id":"brass-pex-x-female-sweat-copper-elbow-90-1-2-3-4-solder-transition-fitting-lead-free-c46500-cupc","title":"1\/2\" Brass Female Sweat × PEX 90° Elbow (F1807) — Lead-Free C46500, cUPC","description":"\u003cp\u003eCopper comes out of the wall and PEX needs to turn — the brass female sweat × PEX 90° elbow handles both in one forged piece. On one end, a solder cup that sweats onto standard 1\/2″ copper; on the other, a 1\/2″ ASTM F1807 crimp barb, set at a right angle so a retrofit line changes direction the moment it changes material. That geometry earns its keep in tight renovation spaces, replacing a sweat elbow, a nipple, and a transition coupling with a single fitting — fewer joints, fewer places to leak behind a sealed wall. Forged from lead-free C46500 brass, cUPC certified and rated to NSF\/ANSI 61 for potable water and hydronic service, it installs in the order every plumber knows: solder first, let it cool, then crimp — the barb never sees the torch. One for the service call, or the 25-pack for crews that spend their weeks converting old copper to new PEX.\u003c\/p\u003e","brand":"DN Group Inc.","offers":[{"title":"1 Pack","offer_id":42357004304478,"sku":"6110011-BPSE","price":2.37,"currency_code":"CAD","in_stock":true},{"title":"25 Pack","offer_id":42357006860382,"sku":"6110011-BPSE-25","price":53.24,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0605\/0073\/8142\/files\/025BDBB5-EF08-472D-9D61-050AE3428474.png?v=1767751770"},{"product_id":"brass-pex-female-sweat-adapter","title":"1\/2\" Brass PEX × Female Sweat Adapter — F1807 to Copper, Lead-Free","description":"\u003cp\u003eHalf the plumbing in the country is copper, and half the repairs happen in PEX — the female sweat adapter is where the two eras meet. Its cup end solders over standard 1\/2″ copper pipe with ordinary flux and lead-free solder; its other end is a 1\/2″ ASTM F1807 barb that crimps to PEX with a copper ring or stainless steel pinch clamp. That makes it the fitting for extending a copper trunk in PEX, repairing a burst section without repiping the house, or landing a new fixture off a fifty-year-old riser. Forged from lead-free brass for potable hot and cold service, it installs in the order every plumber knows: sweat the copper joint first, let it cool, then crimp the PEX — the barb never sees the torch. Sold as a single for the service call or a 50-pack for the crew that lives in retrofit work.\u003c\/p\u003e","brand":"DN Group Inc.","offers":[{"title":"1 Pack","offer_id":42972860186718,"sku":"611611-BPSA","price":1.24,"currency_code":"CAD","in_stock":true},{"title":"50 Pack","offer_id":42972860219486,"sku":"611611-BPSA-50","price":55.75,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0605\/0073\/8142\/files\/6FACC37D-08A7-4C01-9EAA-4D5586CBD9C6.png?v=1783269523"},{"product_id":"brass-pex-mpt-adapter","title":"1\/2\" Brass PEX × MPT Adapter (F1807) — Male Thread, Lead-Free","description":"\u003cp\u003eThe port is female and the PEX needs in — the brass PEX × MPT adapter is that fitting. On one end, a 1\/2″ tapered male NPT thread that seats into shower valves, manifold ports, stop valves, and any standard FIP opening; on the other, a 1\/2″ ASTM F1807 barb that crimps to the tubing with a copper ring or stainless steel pinch clamp. Machined from lead-free brass for potable hot and cold service, it needs nothing but PTFE tape and a wrench on the threaded side and the usual crimp tool on the other — no torch in the sequence, which is what makes threaded transitions the go-to near finished walls and inside cramped vanities. The straight body keeps full flow between thread and tubing, and the taper does the sealing the way NPT always has. Sold as a single for the service call or a 25-pack for the van that never wants to run out of the fitting every job seems to need.\u003c\/p\u003e","brand":"DN Group Inc.","offers":[{"title":"1 Pack","offer_id":42972996796510,"sku":"611711-BPMA","price":2.24,"currency_code":"CAD","in_stock":true},{"title":"25 Pack","offer_id":42972996829278,"sku":"611711-BPMA-25","price":50.4,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0605\/0073\/8142\/files\/ChatGPTImageDec12_2025_04_54_26PM.png?v=1765576475"}],"url":"https:\/\/gdbuildingsupply.com\/collections\/pex-fittings-tubing.oembed","provider":"Good Day Building Supply Inc.","version":"1.0","type":"link"}